Repair Xerox Phaser 8550 Error Timeout Tutorial

Home > Xerox Phaser > Xerox Phaser 8550 Error Timeout

Xerox Phaser 8550 Error Timeout

No problems with print heads using re-cast ink?Thanks for the info. Privacy Policy Site Map Support Terms of Use Search Fixya Home Page Not Found Page Not Found The page you've requested was not found. Join and Comment By clicking you are agreeing to Experts Exchange's Terms of Use. All rights reserved. navigate here

Thanks for mentioning other episodes. The X-Axis motor is not drawing the expected power. Page 122 3-54 Jam Code Troubleshooting Procedures (Continued) Tray 1 width sensor during Tray 1 pick. 1. Page 77: Xx.4x Errors - I/o Circuit Board Fault, Xx.6x Errors - I/o Board Program Faults 2,0XX.4x Errors - I/O Circuit Board Fault 2,0XX.6x Errors - I/O Board Program Faults Phaser

If there isn't a difference I will try recasting it. - Shabbadang 0 A xerox tech told me that the ink for the 8860 is the same ink per se as Page 160 4-30 Paper is picked and moved through either the duplex paper path to determine the paper trailing edge bounce interval at each paper path sensor. Process motor stalled while the printer performed an oil transfix roller cycle. The printhead may need to be renormalized (a manufacturing function). Ошибка контрольной суммы (четности) считывания данных головкой из NVRAM, повреждение программы, неисправность NVRAM. 4,005.44: PC_DEV_FAULT_DM _CAM_ERR Failure positioning drum maintenance cam

Ensure ground integrity (see “Ensuring Ground Integrity”... Tray 3 pick flag triggered unexpectedly while picking from Tray 2. Page 53 Phaser 8400/8500/8550/8560 Color Printer Service Manual The DC power supply generates + 3.3 V, +/- 15 V, and +/- 50 V. Phaser 8500/8550/8560 printers have a solenoid (Head Tilt Solenoid) that is actuated and deactuated when the tilt cam gear rotates to the respective engaged and disengaged positions.

I find it ridiculous. Tray 2 Pick Clutch Tray 3 Pick Clutch Tray 4 Pick Clutch... We print high volume and try to do whatever to keep costs down. The oil is contained in porous foam rollers made from rolled paper/fiber material.

Electronics Troubleshootingpage 181................................................................................................................................................................ Failure reading printhead NVRAM data: check the wiring to the printhead, I2C bus and other hardwar Ошибка чтения данных головкой по шине I2C с памяти NVRAM 4,002.41: PC_DEV_FAULT _HEAD _ZEROS Printhead Restore password × Upload manual upload from disk upload from url Thank you for your help! After letting the molds cure overnight, I carefully cut them open down the middle to get the legit blocks out, expecting to find that all the movement at the beginning had

Is the wiring damaged? Off fe settling time (sec). On-site Printhead Troubleshooting Checklist (8400)page 360................................................................................................................................................................ Most any old HP deskjet or whatever.

Problem is, the yellow ink sticks are getting hard to find. check over here Page 24: Menu Maps, Control Panel Shortcuts Ready) temperatures to reach the proper operating values. Deskew Sensor in unexpected state. 1. Page 151 Phaser 8400/8500/8550/8560 Color Printer Service Manual Tray 2, Tray 3, and Tray 4 Pick Shaft (Continued) Typical Value (8400) R# Definition On fe settling time (sec).

I would like to keep it turned off most of the time, but Xerox tells me that the printer will be damaged if it is turned off for a too long Most of the wax end up in the waste tray. Ensure the Process Drive is correctly aligned, refer to “Homing the Process Drive Train”... http://thatcom.net/xerox-phaser/xerox-phaser-8550-printer-error-codes.html Any changes or modifications not expressly approved by Xerox could void the user's authority to operate the equipment.

this acts as a reset. Your only altenative is to use 3rd party ink which is cheaper by wpc on Mar 19, 2008 at 8:12am Add comment Please sign in to comment 0 Thanks for the That seems to be the case.I purchased 4 super-cheap square cake pans (easier to poor the melted ink); one for each color.

Make it the default.

Page 45: Drum Maintenance Kit Drum Maintenance Kit Phaser 8400/8500/8550/8560 Color Printer Service Manual The Drum Maintenance Kit creates a thin layer of silicone oil on the surface of the Drum Anyone have an idea? Page 116: Jam Codes Jam History and press OK to display the most recent jam list. I see there's an 8560 for sale but the ink sticks I have for the 8550 won't fit in the 8560 (I think) and I don't want to shave them or

I own a Xerox Phaser 8550 since a few years back, and I since I have read lots of entries here on this printer, I think we all agree that the Check the drum maintenance cam solenoid, clutch, home sensor, and related hardware. Ошибка положения узла чистки барабана переноса изображения в процессе процедуры чистки. 4,012.42: PC_DEV_FAULT_DM_ CAM_END At the end of a The problem is that XP does not truly remove it all, so that a bad install can still be there. http://thatcom.net/xerox-phaser/xerox-phaser-3600-pcl-6-error.html The Process Drive is able to actuate each camshaft system independently through the use of the swing arm in the gear train.