How To Fix Write Error Rate C8 (Solved)

Home > Write Error > Write Error Rate C8

Write Error Rate C8

Errors are normal and the drive should be able to correct them which is also normal.Click to expand... status bad backup and replaceThe hard drive plugged into SATA 2 is my 1TB Samsung HD103SJ. I haven't pre-cleared the disk yet. Code: HD Tune Pro: SAMSUNG HD204UI Health ID Current Worst ThresholdData Status (01) Raw Read Error Rate 100 100 51 0 ok (02) Throughput Performance 252 252 0 0 ok (03)

I had to cut it short as I had to leave but it checked over half of the files and found no differences. Though it varies as well to 20 MB/s, 10 MB/s. but I'll replace them with WD drives eventually. My current/worst values are still at the default (like yours), which is the only thing giving me optimism at this point.

my replacement came 7 days after I contacted samsung for warranty, (fast turnaround!) and now my new drive has this increasing number of Write Error Rate too. (at 4007 currently) but Not sure if this would make a difference. Is there any jumper seting on these drives to knock them down to SATA-150?Click to expand... Peteman100, Dec 31, 2010 Peteman100, Dec 31, 2010 #2 Jan 2, 2011 #3 Mav451 2[H]4U Messages: 4,066 Joined: Jul 23, 2004 I'm seeing the same behavior on my WD10EALS.

I've booted to a Ubuntu 10.10 live CD and so far copied 450 GB to the aforementioned HDD with no increase in write errors. If this is true it does not seem to have worked. The problem isn't the HD but the controller, and not because it's maximum speed is SATA-150 but because it was designed wrong. but just to reply to Janmae: my G-Sense error rate has stayed almost constant since I bought the drives.

I believe you should just RMA the drives that you are having problems with.Click to expand... Write errors are still increasing. My HD204UI's do not have a write error rate value. Site Changelog Community Forum Software by IP.Board Sign In Use Facebook Use Twitter Need an account?

Sorry for the late reply. I just got one recently (same model from an RMA) Those SMART reports are harder to read than some other SMART monitoring app's. So do I need to go though the long process of a factory RMA immediately or has a failing psu and possible underpowered psu caused a minor damage with a high The 200 (current) / 200 (worst) thing means almost nothing.

C6 Uncorrectable Sector Count 567 OK 196 196 0 N.A. SCT Feature Control supported. I am going to leave this going until it copies the full 1.5 TB. See the following thread: This article explains the SMART attributes:

Code: [emailprotected]:~$ sudo smartctl -a /dev/sdd smartctl 5.40 2010-03-16 r3077 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, === START OF INFORMATION SECTION === Device Model: SAMSUNG HD204UI Serial Register a new account Sign in Already have an account? I had Samsung 1TB (HD103SJ) and 2TB (HD204UI). Why is this C++ code faster than my hand-written assembly for testing the Collatz conjecture?

Print a letter Fibonacci How can ransomware know file types? I mention that because its common knowledge these programs and similar can cause corruption etc.. Several functions may not work. this contact form See topic WD10EFRX SMART-errors but status is OK in this forum.

HD Tune: SAMSUNG HD155UI Health ID Current Worst ThresholdData Status (01) Raw Read Error Rate 100 100 51 0 Ok (02) Throughput Performance 54 54 0 15855 Ok (03) Spin Up It's easy! but might not be critical until you reach 100.

How did your out-of-case experiment go?

BleepingComputer is being sued by Enigma Software because of a negative review of SpyHunter. In either case I am not seeing any excessive Multi Zone Error Rates for either of my 3 Samsung F4s at home. General Purpose Logging supported. Is it perhaps relative to attribute 09 - Power On Hours Count?

I tried numerous times and the only way I got it to work was with a flash drive with FreeDOS. Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the Here is the spec: ASUS P8H67--M PRO i3 2120 8GB Corsair XMS3 It has one 500 GB Seagate 7200.12 HDD which is not suffering from any problems. navigate here Probably cheaper for the company to just replace em.

memphis_1220, Feb 21, 2011 memphis_1220, Feb 21, 2011 #6 Feb 21, 2011 #7 Relativistic n00bie Messages: 54 Joined: Jan 20, 2010 Can you query the drive using the latest version of My tests comprise of duplicating a 2.4 GB file full of alphanumeric characters. The Samsung 1TB & 2TB drives are programmed to be very Highly Sensitive to vibration.