How To Repair Winsock Error 10065 Host Unreachable (Solved)

Home > Socket Error > Winsock Error 10065 Host Unreachable

Winsock Error 10065 Host Unreachable

Contents

Typically, only one usage of each socket address (protocol/IP address/port) is permitted. The ICMP message means that a router cannot forward the IP datagram, possibly because it did not get a response to an ARP request (which might mean the destination host is An overlapped operation was canceled due to the closure of the socket, or the execution of the SIO_FLUSH command in WSAIoctl. To be able to send outbound mail, there must be a protocol and site&content rule allowing it. have a peek here

See also: These point to other errors that are similar. ERROR:> Failed to establish data socket. See ASP.NET Ajax CDN Terms of Use – http://www.asp.net/ajaxlibrary/CDN.ashx. ]]> It appears that you have Javascript disabled or your User suggestions: Some network systems have commands to report statistics.

Socket Error 10065 No Route To Host

Winsock functions: bind(), connect(), listen(), FD_CONNECT WSAEADDRNOTAVAIL (10049) Cannot assign requested address. If you are using a host table exclusively, you'll need to update it to add the destination hostname and address. An attempt was made to access a socket in a way forbidden by its access permissions. That public server hosts a few different servers (VPN, SMTP, remote administration) without prohibiting access.Keep in mind, I telnetted outbound to their SMTP server.

An incorrect number of QoS FILTERSPECs were specified in the FLOWDESCRIPTOR. Berkeley description: Only one usage of each address is normally permitted. You should simply ignore this error when it occurs. Winsock Error 10061 a long zero) in the sockaddr_in structure passed to.

You need to call to translate a constant value to network byte order before assigning it to the sin_port field in the sockaddr structure.you tried to connect to the wrong destination 10060 Socket Error No such service is known. WinSock description: Same as Berkeley. I strongly suggest it, especially when Web Publishing and VPN is used.

COMMAND:> LIST STATUS:> Connecting ftp data socket xxx.xx.xxx.xx:xxxx... How To Fix Socket Error 10060 See also: WSAEINVAL WSAENOTCONN (10057) Socket is not connected. The requested protocol has not been configured into the system, or no implementation for it exists. you're trying to share a socket between tasks).

10060 Socket Error

The software caused a connection abort because there is no space on the socket's queue and the socket cannot receive further connections.WinSock description: Partly the same as Berkeley. With the connection close the number of bytes transferred in/out is also shown. Socket Error 10065 No Route To Host WSAEINTR 10004 Interrupted function call. Socket Error 10061 Connection Refused yes, inbound mail works2.

Our email server has no route to their primary MX, so it defaults to their backup, which denies relaying from us to them..said by phriday613: -----Original Message-----From: System AdministratorSent: Thursday, September 08, navigate here In most cases, the default Winsock that comes with your OS is appropriate. it may occur when a pointer to a structures is invalid or when a value in structure field is invalid). If you used a hostname, did it resolve to the correct address? Winsock Error 10060 Mdaemon

This error often occurs when you try to connect in PASV mode to a server that prefers PORT for data connections. The software caused a connection abort because there is no space on the socket's queue and the socket cannot receive further connections. Note that this error is returned by the operating system, so the error number may change in future releases of Windows. Check This Out before calling connect() or accept()).

Not implemented: Name server does not perform specified operation. Socket Error 10060 Connection Timed Out Berkeley description: An operation that takes a long time to complete (such as a connect()) was attempted on a non-blocking socket. (see ioctl()). WSA_QOS_GENERIC_ERROR 11015 QoS generic error.

I guess it doesn't.

Subject: test Sent: 8/10/2005 11:00 AMThe following recipient(s) could not be reached: '[email protected]' on 8/10/2005 11:01 AM You do not have permission to send to this recipient. Is this correct?3. The ICMP message means that the router can't forward the IP datagram, possibly because it didn't get a response to the ARP request (which might mean the destination host is down).User Error Code 10060 Socket Connection Failed By calling shutdown() you do a partial close of a socket, which means you have discontinued sending.

User suggestions: see WSAHOST_NOT_FOUND for details. The attempted operation is not supported for the type of object referenced. The support for the specified socket type does not exist in this address family. this contact form Berkeley description: Some invalid argument was supplied (for example, specifying an invalid level to the setsockopt() function).

Edited by Merlin (06/01/03 04:14 PM) _________________________ DALnet: #HelpDesk, #mIRC, #MISHScript - Undernet: #mIRC, #mIRC-Scripts Top Previous Topic Index Next Topic Preview Hop to: News and Discussions ------Latest NewsGeneral DiscussionSupport ------mIRC In it's place, WinSock uses the error WSAENETUNREACH, exclusively. Specifically, v1.1 WinSock spec notes that this error occurs if the length of the buffer is too small. Microsoft C description: Permission denied.

The file handle supplied is not valid. No more results can be returned by the WSALookupServiceNext function. My crappy webhosting company decided to just remove the files from the PM folder without telling me, and then took 5 days to restore them. The application has initiated an overlapped operation that cannot be completed immediately.

WSAEDQUOT 10069 Disk quota exceeded. User suggestions: It may indicate that there are too many WinSock applications running simultaneously, but this is unlikely since most network systems have many socket handles available. Check the destination address you are using. Another possible reason for the WSAEACCES error is that when the bind function is called (on Windows NT 4.0 with SP4 and later), another application, service, or kernel mode driver is bound to

copies what it can into your buffer) and fails the function. Developer suggestion: are you trying to use an optional feature? For example, the optional type SOCK_RAW might be selected in a socket call, and the implementation does not support SOCK_RAW sockets at all. WSAENOBUFS (10055) No buffer space available An operation on a socket or pipe was not performed because the system lacked sufficient buffer space or because a queue was full.

The usual example for this is a host name-to-address translation attempt (using gethostbyname or WSAAsyncGetHostByName) which uses the DNS (Domain Name Server).