(Solved) Winsock Error 10064 Tutorial

Home > Socket Error > Winsock Error 10064

Winsock Error 10064

Contents

WinSock description: No equivalent. It is normal for WSAEWOULDBLOCK to be reported as the result from calling connect on a nonblocking SOCK_STREAM socket, since some time must elapse for the connection to be established. A retry at some time later may be successful. Firewall and AV Software Outgoing connections can be affected by the presence of firewall or anti-virus software on the local computer or network connection. check over here

I just realized this isn't the best solution probably. WinSock description: Similar to Berkeley & Microsoft C, but in reference to sockets rather than file handles (although the descriptions in the v1.1 specification say "no more file descriptors available"). WSAEDQUOT 10069 Disk quota exceeded. WinSock description: No equivalent.

Socket Error 10061 Connection Refused

You could also try to resolve another hostname you know should work, to check that the name resolution server application is running. Either can block the ports needed to make a successful FTP connection to the remote server. This error apparently also takes the place of WSAEPFNOSUPPORT (which means 'protocol family not supported'), since that error is not listed for socket. Berkeley description: A socket operation was attempted to an unreachable host.

WSAEHOSTUNREACH 10065 No route to host. User suggestions: Either you went to the wrong host, or the server application you're trying to contact isn't executing. Additional functions: a generic description of the type of functions that can return this error, which may include functions other than those listed by the WinSock specification. Socket Error 10061 Connection Refused Windows 7 If a server name was used, verify it resolves to the correct address.

WSAESTALE 10070 Stale file handle reference. Winsock Error 10061 However, it is interchangeable in most cases, and all Windows Sockets functions that return one of these messages also specify WSAEAFNOSUPPORT. WSAESOCKTNOSUPPORT 10044 Socket type not supported. You cannot mix and match. (WINSOCK DLLs must be supplied by the same vendor that provided your underlying protocol stack).You cannot use more than one Winsock implementation simultaneously.If you have more

WSAEWOULDBLOCK 10035 Operation would block. Winsock Error Code 10061 Exchange 2013 WSAEADDRINUSE (10048) Address already in use. WSAEALREADY (10037) Operation already in progress An operation was attempted on a non-blocking object that already had an operation in progress.WinSock description: WSAEALREADY means that the asynchronous operation you attempted to Since Windows Sockets is practically a clone of Berkeley Sockets, and the rule of thumb is "when in doubt, defer to Berkeley", we can adopt the Berkeley Software Distribution error text

Winsock Error 10061

a TCP reset received from remote host). You cannot use more than one WinSock implementation simultaneously. Socket Error 10061 Connection Refused If the hostname resolution uses a local host table, it's possible you resolved to an obsolete address. What Is A Socket Error Berkeley description: An operation on a socket or pipe was not performed because the system lacked sufficient buffer space or because a queue was full.

you tried to connect to the wrong destination host address the server application isn't running on the destination host the server application isn't listening on the right port. check my blog No more results can be returned by the WSALookupServiceNext function. Developer suggestions: Did you close a socket inadvertently in one part of an application without keeping another part notified? These error codes and a short text description associated with an error code are defined in the Winerror.h header file. Winsock Error 10060

WSAEDESTADDRREQ 10039 Destination address required. WSAEADDRINUSE (10048) Address already in use Only one usage of each address is normally permitted. WinSock functions: bind(), connect(), sendto(), socket(), FD_CONNECT See also: WSAEPROTOTYPE WSAEALREADY (10037) Operation already in progress. this content Verify that the destination IP address is correct.

WSAECONNABORTED 10053 Software caused connection abort. Socket Error 10061 Connection Refused Smtp If it persists, exit Windows or reboot your machine to remedy the problem. This error is also returned if the service provider returned a version number other than 2.0.

A general QoS error.

we don't recommend it). Check your WinSock implementation documentation to be sure all necessary components are currently installed and configured correctly. However, there's little distinction between WSAEALREADY and WSAEINVAL since a WinSock DLL cannot tell the difference between an asynchronous operation that has been cancelled and one that was never valid. Socket Error 10061 Ppsspp The ICMP message means that the router can't forward the IP datagram, possibly because it didn't get a response to the ARP request (which might mean the destination host is down).

This is a common problem. The explanation is simple and obvious: in order to connect to or send to a destination address, you need to provide the destination address. connect(), send(), recv(), et cetera). have a peek at these guys If you continue to receive the same error after insuring ports 20 and 21 are open, contact the administrator of the site you are trying to connect to.

If the hostname resolution uses a local hosttable, it's possible you resolved to an old obsolete address. WinSock description: No equivalent. For example, you shouldn't necessarily expect to be able to use NS addresses with ARPA Internet protocols. In this case, the 2nd application will fail with WSAEADDRINUSE.

For instance, this error will occur if you try to run two applications that have FTP servers. Ignore it. This could indicate a serious failure of the network system (that is, the protocol stack that the Windows Sockets DLL runs over), the network interface, or the local network itself. WinSock description: NOT same as Berkeley, but analogous.

Under MS-DOS versions 3.0 and later, EACCES may also indicate a locking or sharing violation. The support for the specified socket type does not exist in this address family. The WinSock API does not provide access to the Network File System application protocol, so this error is irrelevant to WinSock. This may indicate the file was deleted on the NFS server or some other catastrophic event occurred.

Ping a local host to verify that your local network is still functioning (if on a serial connection, see next step) Ping your local router address. WinSock description: No equivalent in WinSock. The file's permission setting does not allow the specified access. WSAEACCES 10013 Permission denied.

The "address" it refers to is the remote socket name (protocol, port and address). WinSock functions: WSACancelAsyncRequest() Additional functions: Berkeley sockets connect() returns this error on subsequent calls, after an initial call on a non-blocking socket. File unavailable (file busy). 451Requested action aborted: local error in processing. 452Requested action not taken. All rights reserved.

If you are using a host table exclusively, you'll need to update it to add the destination hostname and address. WinSock description: No equivalent WinSock functions: WSAEMFILE (10024) Too many open files. The receiving system just stops receiving and has to close the socket to do so.WSAETOOMANYREFS (10059) Too many references, can't splice There are too many references to some kernel-level object; the