(Solved) Winsock Error 10063 Tutorial

Home > Socket Error > Winsock Error 10063

Winsock Error 10063

Contents

WSA_QOS_NO_RECEIVERS 11008 QoS no receivers. Cannot remove a directory that is not empty. See also: WSANO_DATA, WSANO_RECOVERY, WSATRY_AGAIN WSANOTINITIALISED (10093) Successful WSAStartup() not yet performed Berkeley description: No equivalent. Some WinSock implementation use these errors inappropriately, but they have a particular meaning. check over here

The v1.1 specification also lists connect(), although it does not allocate a descriptor. A blocking operation is currently executing. It's also possible that the local services file has an incorrect port number (although it's unlikely). Although some WinSock implementations might not issue other errors if a connection fails, so you can handle this error as you would others that indicate connection failure.

Windows Socket Error 10054

WinSock description: No equivalent in WinSock. In Berkeley, this error also occurs when you are trying to name the local socket (assign local address and port number) with bind(), but Windows Sockets doesn't ascribe this error to For protocol and services resolution, the name or number was not found in the respective database.

Recv and Recvfrom: If the datagram you read is larger than the buffer you supplied, then Winsock truncates the datagram (i.e. copies what it can into your buffer) and fails the function. There is another possibility: you are accessing a socket which the current active task does not own (that is, you're trying to share a socket between tasks). Socket Error Codes Linux The Windows function is indicating a problem with one or more parameters.

WinSock description: No equivalent. Winsock Error 10053 Check that your network system (WinSock implementation) has a utility that shows network statistics. For example, you cannot use the ARPA Internet UDP protocol with type SOCK_STREAM. WinSock description: Same as Berkeley.

WSAENETUNREACH 10051 Network is unreachable. Socket Error 10061 Connection Refused Unlike Berkeley, however, WinSock v1.1 doesn't ascribe this error to any functions. WinSock description: Same as Berkeley. WSAEPROTONOSUPPORT (10043) Protocol not supported.

Winsock Error 10053

Developer suggestions: You need to be prepared to handle this error on any functions that reference blocking sockets, or any calls to blocking functions, if you allow the user to cancel WSAEISCONN (10056) Socket is already connected A connect request was made on an already connected socket; or, a sendto or sendmsg() request on a connected socket specified a destination when already Windows Socket Error 10054 The number is a Winsock error number. What Is A Socket Error This normally results if the peer application on the remote host is suddenly stopped, the host is rebooted, the host or remote network interface is disabled, or the remote host uses

after the first failed with WSAEWOULDBLOCK). check my blog Check whether you have a router configured in your network system (your WinSock implementation). WSAENETDOWN 10050 Network is down. Be aware that without Javascript, this website may not behave as expected. Socket Error 10054 Connection Reset By Peer

Additional functions: With a datagram socket: send() or sendto(), or FD_READ. This error apparently also takes the place of WSAEPFNOSUPPORT (which means "protocol family not supported"), since that error is not listed for socket() in the v1.1 WinSock specification. No such service is known. this content WSANO_DATA (11004)* Valid name, no data record of requested type The requested name is valid, but does not have an Internet IP address at the name server.

An invalid QoS filter type was used. Winsock Error Windows 7 Berkeley description: The support for the socket type has not been configured into the system or no implementation for it exists. Winsock description: Winsock doesn't support the sendmsg() function, and some Winsock implementations are not so strict as to require an application with a datagram socket to 'disconnect'--by calling connect with a

TCP/IP scenario: The local network system can generate this error if there is no a default route configured.

You could also try to resolve another hostname you know should work, to check that the name resolution server application is running. Users should check: That the appropriate Windows Sockets DLL file is in the current path. WSAENOTCONN 10057 Socket is not connected. Socket Error 11004 Berkeley description: The quota system ran out of table entries.

For instance, even if you request to send() a few bytes of data on a newly created TCP connection, send() could fail with WSAEWOULDBLOCK (if, say, the network system has a after the first failed with WSAEWOULDBLOCK). To recover the orphaned sockets, you can try closing the application and restarting it to recover the open sockets; you may have to end all Winsock applications (to force an unload have a peek at these guys try to ping the server(s)).

WSEACCES 10013 Permission denied.