Repair York Affinity 8 S Series Error Codes Tutorial

Home > Error Codes > York Affinity 8 S Series Error Codes

York Affinity 8 S Series Error Codes

Contents

I tried holding down the START button but it still doesn't work. Glad you found out what was going on and got it fixed. I have also removed the burner cover and tried to start it but while it didn't work initially, it did start later (the only time it's worked since initially giving the Two amber flashes signal normal operation with a call for heat, meaning the wall thermostat is currently telling the furnace to produce heat. http://thatcom.net/error-codes/york-affinity-furnace-error-codes.html

Dyson vacuum ruining carpets or not good for carpet warranty [HomeImprovement] by HBuilder328245. The rollout switch (on the side of the burner box) is a manual reset switch and you reset it by pressing the button in the center. The 2 green colored flashes you are seeing also means that no stored error codes are being found.If there’s 3 green colored flashes, please see the meaning for 2 green colored Also, the new board is not communicating to the front end.

York Furnace Error Codes

I had set the thermostat to cool the house while I was out and when I returned home it had switched off. Check for proper gas flow. 1 RED FLASH: This indicates that flame was sensed when there was not a call for heat. I get the listed flash codes, but why am I getting 27 flashes? I could not find anything wrong while I was there so I checked the last error codes.

I do not have a bypass plug to bypass the economiser option . The furnace will lock out for one hour and then restart. 9 RED FLASHES: Indicates reversed line voltage polarity or grounding problem. I had no idea the Energy Star sticker was placed over the window and all I had to do was lift the sticker. Rheem Furnace Error Codes Six red flashes indicate a current failure on the modulating gas valve.

Thanks for taking the time to read my postings! Carrier Furnace Error Codes All rights reserved. © Applianceblog.com 2004 - 2016 Ask Remember Me? Possible causes include an improperly sized ducting system, a dirty air filter, a faulty blower motor, an open fuse on the control board or restricted circulating airflow. For example, six “on” flashes equals a number 6 fault code.

kevin miller 188,576 views 17:13 Loading more suggestions... Carrier Error Codes However, I can't seem to find anything on the subject. Please focus on the content not the person! if it is bypassed and cooling does not come on, remove the P10 plug on the bottom right side of the board and see if you havee 24 VAC from the

Carrier Furnace Error Codes

The control will flash four times as it writes a 30 second delay ON and a 180 second delay OFF to the program. If the main blower is in a “Delay on” mode it will complete it, and any subsequent delay off period. York Furnace Error Codes Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. Lennox Furnace Error Codes Reply yorkcentraltechtalk says: July 16, 2016 at 12:17 pm I would suggest contacting your local York distributor.

Someone pressed a button in an arbitrary way (( yorkcentraltechtalk says: September 21, 2016 at 1:52 pm You should find your local distributor for manuals or you can try http://www.york.com Aleksey this content Operational faults 6,7,8 will be reset. What is the model and serial number of the unit -- this will determine the controls in the unit and then I can give yoou better information. How to Reset a York Diamond 80 Furnace York Furnace Error Codes. York Furnace Red Light Blinking

setpoint is at 10% min damper position and D the loweset temp setting to turn Econ on. I have removed both gray tubes from the pressure switch and made sure they are clear of obstructions. AdamDIY 54,185 views 11:40 How To change a flame sensor on a furnace and what to look for. (Furnace wont stay lit) - Duration: 17:13. weblink what lights are lit on the board?

This could be Caused by a number of problems: faulty inducer, blocked vent pipe, broken Pressure switch hose or faulty pressure switch. 4 RED FLASHES: This indicates that the main limit Lennox Furnace Diagnostic Codes Is there an economizer in the unit? The LED will flash “7” during this lockout.A Yellow LED labeled “FLAME” is provided to indicate flame statusFlame Status - When flame is sensed, the flame LED is lit.

NOTE: An LED that is not lit may be an indication that the board is not energized.  This could be due to no power or a shut down circuit.

Make a service call. Got the 10 year parts and labour warranty. Two green flashes and three green flashes may appear after attempting to retrieve any stored error codes, and both signal that there are no error codes stored in the memory system. Bryant Furnace Error Codes Next to the light is a NUMBER.

Check polarity at furnace and branch. says: September 3, 2015 at 7:11 pm Will Give it a shot first thing in the morning. Even two or three flashing green lights means that the furnace is producing heat normally. http://thatcom.net/error-codes/zwx1605w-error-codes.html This feature is not available right now.

Temp sensor checked good. Lockout may be manually reset by removing power from the control for more than 1 second or removing the thermostat call for heat for more than 1 and less than 20 Check the pressure switch hose of your furnace for blocks or an improper connection. Helpful Reply We'd like to understand what you find wrong with Juliego's answer: What's inaccurate about this answer?

If you have misplaced, the manual, here are the fault codes with possible problems/solutions below: SLOW GREEN FLASH: Normal operation. This switch can be reset by pushing the center of the red button on your furnace ( it should be located on the side ).6 red colored flashes on your furnace The furnace will lock out for one hour and then restart. 7 RED FLASHES: This fault code indicates that the flame could not be Established. This must indicate a faulty pressure switch if it's so temperamental, right?

The air flow will not operate as it should when you see this error code.5 amber/yellow flashes on your York Furnace signifies that the vent and/or combustion air system is restricted.If Show the error heat delay,Lead leg and fan off. While a Twin Fault exists, the control does not respond to thermostat commands and flashes "5" on the status LED. Sign in Don't like this video?

There is 24volts at Y-out and Econ at the board. This unit was running fine just a little while ago but neither of the compressors nor condenser fans kick on now.