Fix Xrc Error Codes (Solved)

Home > Error Codes > Xrc Error Codes

Xrc Error Codes

Contents

Insert the circuit board in the CPU rack or the connector on the circuit board fast. In this case, alter the teaching. Alarm 1.1 Outline of Alarm When the alarm of level 0-3(major alarm) occurs, the servo power supply is interrupted. Check the motion status of robot again and reduce the teaching speed. http://thatcom.net/error-codes/zwx1605w-error-codes.html

Data stands for the damaged parameter file. 0:RC*, 1:RO*, 2:SV, 3:SVM, 4:SC, 5:SD*, 6:CIO*, 7:FD*, 8:AP, 9:RS, 10:SE, 11:RMS*, 12:AMC*, 13:SVP*, 14:MF*, 15:PCD* *:System parameter The system configuration data information on or what could be the cause? The connection of communication cable for servopack was not cut. name: MRS51020TOC.FM 1.

Motoman Xrc Error Codes

Specify the error point and replace the lead wire. Set the function of the sensor circuit board on maintenance mode again. Then confirm the reoccurrence.

name: MRS51020-CH1.FM Created: 98-08-19 Revised: 99-08-27 Alarm Message List Alarm Number Message MEMORY ERROR(PCIBUS COMMON RAM) [Decimal Data] Cause A error occured in PCI bus shared RAM of the CPU rack Replace the circuit board If the error occurs again, contact MOTOMAN service. Check that the type of motor is the same as the one described in the manual. Motoman Error 0380 Insert the circuit board in the CPU rack or the connector on the circuit board fast.

Check the connection of the terminal connector(WRCA•CN10(#*)). Motoman Dx100 Error Codes Always return the programming pendant to the hook after use. The connection of terminal connector was not completed. If the error occurs again, contact MOTOMAN service. 1202 FAULT [Decimal Data] CPU motion impossibility caused by 0 division etc.

Replace the XCP01, I/O contactor unit, I/O module. Motoman Xrc Alarm List Insert the circuit board in the CPU rack or the connector on the circuit board fast. If the error occurs again, contact MOTOMAN service. Remedy Connect the battery with the encoder.

Motoman Dx100 Error Codes

Remedy Insert the circuit board in the CPU rack or the connector on the circuit board fast. In this manual, the Notes for Safe Operation are classified as “WARNING” or ”INFORMATION”. Motoman Xrc Error Codes If the phenomenon occurs again after repeating this operation several times, replace the WRCA01 circuit board, amplifier for the axis where the error occurred. Motoman Nx100 Alarm Codes MOTOMAN is not responsible for incidents arising from unauthorized modification of its products.

Replace the XCP01 circuit board. http://thatcom.net/error-codes/xtl-2500-error-codes.html If the error occurs again, replace the WRCA01, WRCF01 circuit board. The cable between the XCP01 circuit board and WRCA01 circuit board was defective. Load the ladder program saved on the external memory unit. Motoman Dx100 Maintenance Manual

If the error occurs again, contact MOTOMAN service. 1338 SPEED MONITOR LEVEL ERROR The error occured on speed monitor level signal (signal error). 1339 SPEED MONITOR LEVEL ERR (XFC01) The error Do. If the alarm doesn't reoccur, alter the load. weblink Turn the power off then back on.

Insert the circuit board in the CPU rack or the connector on the circuit board fast. Motoman Xrc Controller Manual Check the primary power supply(220V, +10%). Read this manual carefully and be sure to understand its contents before handling the MOTOMAN XRC.

The set up of the WRCA01, XCP02 circuit board was not completed.

If the wires are conducted, it's abnormal. It interfered with an outside equipment. Check that the type of motor set by system configuration is same as actual installed one. Motoman Dx200 Alarm Codes Insert the circuit board in the CPU rack or the connector on the circuit board fast.

If set data by system configuration is correct, replace installed motor with correct one. Insert the circuit board in the CPU rack or the connector on the circuit board fast. If the type is not correct, replace it with the correct motor. check over here I can compile this application under Linux without errors (I use Gentoo Linux and Kdevelop) but I get some errors in the shell (see my first post).

Check the robot motion on alarm and check whether external power is operated or not. Yes, it should be, but I confess that I never use XRC not do I plan to use it soon, so that's my reason not to answer: I simply know nothing Insert the circuit board in the CPU rack or the connector on the circuit board fast. If set data by system configuration is correct, replace installed motor with correct one.

Check the primary power supply voltage (220V+10%). If the type is not correct, replace it with the correct motor. The wrong wiring, the breaking of the UVW wire for the motor The type of motor was not correct. Your cache administrator is webmaster.

If the wires are conducted, it is thought to be a defective lead wire. Changed the contactors and all was well. The system configuration setting of encoder was not correct. Turn the power off then back on.

I allowed the software to download and install an update when I launched FZ. Replace the circuit board. Insert the circuit board in the CPU rack or the connector on the circuit board fast. If the error occurs again, replace WRC01 and/or WRCF01 circuit board. 1307 1308 OVER SPEED Robot/Station [Axis Data] The motor speed displayed by axis data exceeded allowable max speed.

name: MRS51020-CH1.FM Alarm Number Message MEMORY ERROR (CPU BOARD RAM) [Decimal Data] Cause Memory(RAM) error Data stands for an error circuit board 1:XCP01 circuit board 2:XSP01 circuit board 10:XCP02 circuit board If the error occurs again, replace the WRCA01 circuit board and the converter. Replace the circuit board. Isolabls_1198_1956.pdfUnited States v.