Repair Whirlpool Duet Error Code F32 (Solved)

Home > Error Code > Whirlpool Duet Error Code F32

Whirlpool Duet Error Code F32

Contents

ft. Unplug washer or disconnect power. 2. Check connections of the CCU board within the housing. Diagnostic shows ' F 32 ' & ' F 33 '. Source

Check if the airtrap is not blocked. 3. Check wire harness connections to the User Interface and the Central Control Unit. 3. I found this out because i tested the pressure switch. Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU) Check/Clean Drain Pump Filter of foreign objects Check for Drain Pump Failure Check the Inlet Valve

Whirlpool Cabrio Washer F32 Error Code

I picked up a new "pressure switch" and also a "drain pump" as I was getting the F21 error code as well. Or just drag it here! Door lock mechanism is broken. NOTE: During first power up of new CCU and UI combination, a bootphase (uploading parameters) will be performed.

Verify inlet valve operation. Press PAUSE/CANCEL two times to clear the display. 1. We sucked up a carpenter pencil. Up next How to Test the Pressure Switch on your Washer - Not Filling or Overfilling with Water - Duration: 4:06.

Hard to narrow this one down. Try unplugging the washer for 2 minutes and see if it will do a Duet Washer Quick Diagnostic Cycle F32 Pressure Switch Error The Duet washer uses a pressure sensing switch Posted by Stogiez on May 01, 2008 Want Answer 0 Clicking this will make more experts see the question and we will remind you when it gets answered. 14 Comments Flag Unit is about 3 months old.

If all that looks good check the drain system for blockages or you may have a bad drain pump. F30 DISPENSER SYSTEM ERROR When the dispenser motor cannot be driven to its proper position. 1. Flo See inside of your appliance - diagrams and part photos for virtually every model. Check/clean drain pump filter of foreign objects. 5.

Whirlpool Duet Pressure Switch

Jarred Johnson 39,357 views 4:15 How to Diagnose Washing Machine Control and Program Problems - Duration: 9:08. If there is water in the unit: Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1. Whirlpool Cabrio Washer F32 Error Code The resistance of both door coils (between pin 1 and 3) should be approx. 320 Ω. Whirlpool Cabrio F72 Error Code Ft.

Check calcifi cation of steamer element. this contact form Prevention/Solution Make sure all the tiny wires are not stripped and are properly connected into the pressure switch. In normal use (a little blockage is normal) the steamer cleans itself. What the problem can be: Unplug for an hour and plug it in again and try. Whirlpool Duet Washer Error Codes

It will try to lock it 6 times before displaying the error. Replace the Motor Control Unit. Check the connections between the Steamer 3. have a peek here If "Sud" is displayed a potential suds lock is detected.

After reassembling the washer, it worked just fine. Unplug washer or disconnect power. 3. Same problem only we just had machine delivered today.

Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and b etween the MCU and the Central Control Unit (CCU).

Verify CCU operation by running a Diagnostic Test or any cycle. 6. He stated that there is a "break in period of about 3 months and that a pressure switch can get kinda delicate." He also noticed that I have the Watts Floodsafe Check the MCU by looking for operations of the drive motor. 5. F03 HEATER SC TO GROUND The Heater has a internal short circuit.

Like ApplianceAssistant on Facebook! Check the water temperature sensor and connection to it. 3. F21 LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off. Check This Out If failure occurs during high-speed spin the door unlocks after 3 minutes. 1.

Try unplugging the washer for 2 minutes to reset the washer's memory. NOTE: During first power up of new CCU and UI combination, a bootphase (uploading parameters) will be performed. Answer. It can be broken or as in my case some how it reversed its output, meaning an empty washer was "thinking" it was full, thus locking the door.

Replace User Interface if drum is rotating. 4. The pressure switch was the problem. My washer had this same error code. F11 MOTOR CONTROL UNIT ERROR The Motor Control Unit has internal failure; repeating under or over voltage, or over current conditions.

Check for plugged or kinked inlet hoses or plugged screens in the inlet valves 3. Plug in washer or reconnect power. 6. Ask Loading...Oops :Please try again. Whirlpool Cabrio WTW6600SBK Top Whirlpool Washing Machines Experts Dan Webster Level 3 Expert 8147 Answers Richard Roth Level 3 Expert 9472 Answers Mike Cairns Level 3 Expert 3053 Answers Are you

Review this data and view the images therein. Whirlpool Duet Error Code F-11. Check mains supply is in range (90V-132V). check that all the connections to the main control are fully connected.