(Solved) Whirlpool Duet Error Code F06 Tutorial

Home > Error Code > Whirlpool Duet Error Code F06

Whirlpool Duet Error Code F06

Contents

Because after verifying the motor windings, tachometer, and motor cable harness, I tapped the tachometer output sensors at the motor control unit (MCU) and connected it to an AC-coupled (but grounded) If it doesn't turn smoothly and easily, you have a bad motor. Please report back here if the motor ends up not being the problem. Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Source

Add to Want to watch this again later? Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. DudeWhitman 50,535 views 3:56 Whirlpool washing machine drain pump replacement and diagnostic - Duration: 17:45. Check the drive system for any worn or failed components.

Whirlpool Duet Washer Error Code F06 E02

here is more info from here Check the MCU. The door opens and closes with no problems. Get cash quickly before your next payday! Cancel Boerre Rep: 1 Posted: 03/18/2015 Options Permalink History Hi, Thanks for all help in this thread.

Might be parts from the Baffles which are not screwed in on my machine but attached with plastic feet that are snapped in and notice a couple are missing upon inspection Thank you for the help. Sign in to report inappropriate content. Whirlpool F06 I will also check the the connections on the MCU.

Working... See Details More Products Whirlpool WFW92HEFU 4.5 cu. At the opposite end, this will be the 2nd connector from the rear on the left-hand side of the CCU. Possible Causes / Procedure Unplug washer or disconnect power.

Working... Whirlpool Duet F6 Error Code I made sure both parts were properly attached. Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. To learn more about your washing machine, or to order parts, click here.

Whirlpool Duet Washer Error Code F06 E01

Remove the connector plug and check across pins 1 to 2, 2 to 3, and 1 to 3. One trick that often works at this point is to remove and reinsert all wire connections at the board and motor. Whirlpool Duet Washer Error Code F06 E02 All rights reserved. Whirlpool Duet Error Code E02 I think this is the last extended protection plan I'll ever purchase....

Please try again later. this contact form Was about to give it all up but then saw there was a second, small wire to the motor. Working... Loading... F06 Error Code Kenmore Elite Washer

Loading... Loading... a restart would result in same code and stopage. have a peek here By GregC in forum Whirlpool/KitchenAid/Roper/Estate Replies: 6 Last Post: June 30th, 2014, 04:30 PM Whirlpool Duet---No error code, BUT......

All rights reserved. © Applianceblog.com 2004 - 2016 Skip to content Sign In Join or Activate Products Departments Departments Shop Shop Explore Explore Advice Advice Rewards Rewards More More Home Whirlpool Carbon Brushes if I press the pause/cancel button while when the timer is not flashing, the machine drains and turns off. Watch Queue Queue __count__/__total__ Find out whyClose WHIRLPOOL DUET / MAYTAG WASHER MACHINE repair error codes F01,F06,E01,E02 C.L.S.

unplug the washer and using a small screwdriver push all the pins inside the plug as far inside as you can.

Transcript The interactive transcript could not be loaded. Harold Jackson 112,525 views 3:39 Whirlpool , KitchenAid & Kenmore Washer is leaking and has a loud spin - GHW9400PW4 - Duration: 57:28. here's the bizarro scenario I find myself in. Whirlpool Duet Washer Error Code E01 When we put heavy load, due to the shaking when spinning, the pins as loose in the plug and when the drum rotates the pins get loose and the MCU cannot

I replaced the Motor Control Unit with one purchased from eBay, and so far the error has not returned and I've used it on large loads with High Speed spin. 11/01/2013 Here is what the F11 means. If any of the Drive Motor windings indicate readings higher that 6 ohms, replace the Drive Motor. Check This Out ft.

I will call the repairman - but will fix it myself if possible. Apply in just minutes. Bought a new washer instead of spending $400.00 for a motor. I don't think the wife will like unplugging the washer for a few minutes everytime it throws this code Last edited by Jake; August 13th, 2010 at 08:06 PM.

Was this answer helpful? Seems there should be a better fix... That is, with the MCU installed, connector 1 is on the bottom, followed by 2 in the middle, and 3 on top. December 1st, 2010,01:47 PM #8 3fordasho View Profile View Forum Posts Premium Member Join Date Feb 2006 Location Minnesota Posts 8 Originally Posted by sandyds how do you reset it?

eSpares 205,966 views 9:08 Whirlpool tumble dryer 6th sense how to clear error codes - Duration: 2:49. When I checked the motor I found that the resistance check on the brushes was three times what it should have been. This video can be used on all these Whirlpool Washing Machine models: WHIRLPOOL AWM 274/1/WS-B Ser.No. 857003120001, WHIRLPOOL AWM 274/1/WS-B Ser.No. 857003120000, WHIRLPOOL AWM 248 Ser.No. 857024810000, WHIRLPOOL AWM 221 Ser.No. 857022115020, ft.

RepairClinic offers the largest inventory of appliance parts for all major brands, including Whirlpool, Frigidaire, LG, GE, Samsung, and many more! The consumer or reader is individually responsible for his or her use of the information supplied and uses this information at their own risk. Checked the resistance of the connector to the motor, and got weird values. Sign in Share More Report Need to report the video?

EastAngliaUK 52,357 views 4:24 Front Load Washer Repair - Not Draining or Spinning - How to Unclog the Drain Pump - Duration: 10:43. Contact your Best buy extended warranty phone number and ask for customer relations to see if they can expedite this.