Repair Vita Spa Error Codes Bj2p Tutorial

Home > Error Code > Vita Spa Error Codes Bj2p

Vita Spa Error Codes Bj2p


OH = Overheating, water over 112° F. Quick View SpaCyclopedia Contact CHECK OUT 0 Your cart is empty.Continue shopping to add items to your cart. Refill, if necessary. Pr = When spa is first actuated, it will go into Priming Mode. Source

COOL = Spa water is more than 20° F cooler than the temperature set point. Check for clogged filter * FL2 : Pressure switch problem. You can leave a response, or trackback from your own site. hot = Overheating, water over 112° F.

Hot Tub Error Codes

Your cache administrator is webmaster. FL = Flow. FL2 = Pressure switch problem. Pressure switch is not working * SN : Non functional high temperature sensor.

Hi limit sensor is disconnected, shorted, or spa temp is above 112° F. * SEoP : Sensor open or disconnected. Spa temp over 108°.  HLoH : Hi Limit Over Heat. SL = Sleep mode Brett Aqualine Control Systems for Spas or Hot Tubs: OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° FFL = Pressure switch Hot Tub Error Code Oh Low speed pump (and air blower if equipped) will activate to lower temp * --- : "Watchdog".

Sn Sensors out of balance Sn1 Hi-limit sensor malfunction Sn2 Nonfunctional temperature sensor. Balboa Hot Tub Error Codes If pump 1 was turned on due to this reason alone, this message will appear for up to two minutes right after very cold water is detected. Contact qualified service technician. Spa unusable.

SN = Non functional high temperature sensor. Sundance Spa Error Codes Spa is shut down. * Pr : When spa is first actuated, it will go into Priming Mode * ILOC : Interlock failure * --- : Unknown water temperature. (Displays when HOT = Circuit Board temperature has exceeded acceptable limit. Sn1 = Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated).

Balboa Hot Tub Error Codes

If alternating with temp, may be temporary condition. Do not enter the spa. Hot Tub Error Codes HFL: Substantial difference between temp sensors detected. Gecko Spa Pack Error Codes In some instances it may be more prudent to contact a local repairman or send Spa Care Center your control box for evaluation/repair.

Heater is deactivated.Sn2 = Nonfunctional temperature sensor. this contact form One sensor has detected 110º. You can often determine the make of the control system by looking inside the spa's equipment area. Inspect these first:• Check slice or ball valves. Marquis Spa Error Codes

drops.HL = High limit switch tripped. Heater is shut down, but other spa functions run normally. Sensor plugged into jack B is not working. The spa is at a temperature above 108° .

ILOC: Interlock failure - possible pump/ozone spike CTI Error Codes thl/39: temp probe problem th2/current temp: temp probe problem th3/39: water temp below 39° F OH: water over 112° F. Spa Command Panel Instructions Dream Maker Hot Tubs OH = Overheat 108° F, spa is deactivated. Spa Builders Spa Side Error Codes Sn1 = Nonfunctional high temperature sensor.

One sensor has detected 110°F.

ILOC = Interlock failure - possible pump or ozone spike . (---) =Unknown water temperature. (Displays when first powered up after refill). Water temperature has reached 118ºF. FL: Flow. Balboa Hot Tub Codes F8 Heater is deactivated.

Check for clogged filter FL2 Pressure switch problem. Std = Spa operating in Standard Mode. Generated Sat, 05 Nov 2016 16:25:18 GMT by s_wx1199 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: Connection th3/39 = On startup indicates water temperature less than 39° F.

Low speed pump and heater will activate until spa reaches 65ºF OH: High temperature condition, has reached 110ºF. Brett Aqualine Error Codes OH: Temp exceeds 118 F Fr: Freeze condition - temp below 40 degrees FL: Pressure switch failure EO: Shorted temp sensor E1: Open temp sensor E2: Shorted Status of the heater element is unknown. Protect from FreezingCover Cleaning and AdviceAcrylic Surface Care and MaintenancePurchase a "Made for Michigan" Spa Cover>Spa Cover MeasuringPurchase a Spa Cover Lift AssistantWhirlpool & Air Bath TubsSystem Cleaning-Home remedyAcrylic Surface Care

the big list of spa and hot tub error codes CODE ERROR CODE DESCRIPTION * * *  Flow/Pressure switch either Open or Closed * * * High Limit switch is faulty OHS: Overheat.. ToE = Time out error. Check for clogged filter.

Click here Welcome to our newest forum for those that was on the old forum we had to update the site so please re-register Free spa / Hottub information and adivce One sensor has detected 110º * Flo : Improper flow or pressure switch malfunction * Cool : Water temp 20 degrees below set point * ICE : Potential freeze condition has SnS = Sensors out of balance. pump will operate continuously until the temperature rises above 45° F.OH = Over heat.

Check water level in spa. One sensor has detected 110ºF.Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit at heater.OHS = Overheat. If you need further help with troubleshooting click here Balboa Spa Side Error Codes pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F.

Wondering what your spa is trying to tell you? PSoC : Pressure switch open with circulation pump.  PSoL : Pressure switch open with low pump.  PSoH : Pressure switch open with high pump.  ToE : Time out error. Check for low water level and ensure pump is primed. If the water is still hotter than the set temperature, press the blower button (if applicable) to cool the spa.If your spa is not overheating based on physical vessel temperature and