How To Fix Vita Spa Error Code P5 (Solved)

Home > Error Code > Vita Spa Error Code P5

Vita Spa Error Code P5

Contents

PSoL = Pressure switch open with low pump. Heater disabled but the spa is operational. drops.HL = High limit switch tripped. Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature. --- = "Watchdog". http://thatcom.net/error-code/vita-spa-error-code-6j2p.html

drops. Working... Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Adding cool water may be necessary.

Hot Tub Error Codes

Sign in to add this video to a playlist. Now the jets have stopped working. Heater is deactivated.FL1 = Water flow problem, inhibited or pressure switch malfunction. SwimUniversity 53,539 views 5:41 How to Diagnose Your Hot Tub Pressure Switch for Flow Problems | Arctic Spas - Duration: 3:41.

Start by checking the heater connections and ensuring that the electrical lines leading to the heater are connected. The Spa or Hot Tub Panel Displays: :IC , iCE This indicates that the auxiliary sensor detects a possible freeze condition. Status of the heater element is unknown. Gecko Spa Pack Error Codes Snb = Spa is shut down.

This is a normal spa function; no further action is necessary.When either sensor reads below 40 degrees F., the system provides freeze protection. If your not sure if you have a flow or pressure switch, you can always email us pictures and your questions at sales@spabrothers.com . Become part of our maker community. Arctic Spas Utah 37,800 views 1:49 No Glitch Flow Switch Installation - Duration: 14:19.

This indicates a persistent flow problem The heater is shut down while all other spa functions continue to run normally. Balboa Spa Control Manual If the fuses are OK, the electrical relay is stuck. drops. Check power connections and rerun diagnostic t e s t Replace underwater light bulb Low Power (voltage) observed.

Balboa Hot Tub Error Codes

FLO = Flow Switch (heater is deactivated. O3, O3S or O3U Errors Anytime O3 appears in an error, it is related to ozone. Hot Tub Error Codes How to Troubleshoot Clearwater Spas See the Clearwater Spa instruction manual for more troubleshooting codes. Vita Spa Troubleshooting If display shows only this message (blinking) spa is shut down.HFL = Substantial difference between temperature sensors detected.

Depending on where the temp sensor is mounted; usually in the wall of the spa in a sensor mount, you could have a flow issue. Check This Out The Spa or Hot Tub Panel Displays: SL This indicates the system is in sleep mode and can be changed by pressing the up temp. Low speed pump and heater will activate until spa reaches 65°F. Check for clogged filter. Marquis Spa Error Codes

Sensor plugged into jack B is not working.SnS = Sensors out of balance. Low speed pump and heater will activate until spa reaches 65ºF. I have you guys bookmarked now for all my hot tub needs and will be referring others to ur site because of ur prompt service and very reasonable prices." - Sarah Source SE = Spa operating in Standard-in-Economy Mode.

If the swicth is a open one. Coleman Spa Error Codes Promoted By Zergnet Comments Please enable JavaScript to view the comments powered by Disqus. Rare system error.

Loading...

Remove the spa cover and allow the water to cool. Hot Tub Repair Codes The codes are often initials that represent a shortened error message. ... Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. Sundance Spa Error Codes th2/current temperature = On startup indicates temperature probe problem.

Pressure switch is not working.SN = Non functional high temperature sensor. Could indicate a flow problem.LF = Persistent low flow problems. (Displays on the 5th occurrence of "HFL" message with 24 hours). ToE = Time out error. have a peek here This is a normal spa function; no further action is necessary.When the auxiliary sensor reads around 40F- (actual temperature dependent on specific auxiliary sensor used), the system provides freeze protection.

For more information regarding CTI tech support click here Blue Ridge Spa Side Error Codes (click here) Gatsby Spa Spa Side Error Codes (click here) Imperial Spa Spa Side Error Codes FLO Lack of Flow:Heater disabled CS Current Sensor F1 or F2 Blown Fu s e HC Heater Error HP High Vo l t a g e LB Light Error LP Low In most cases overheat issues are related to the relays on the circuit board, or the temp sensor has failed and will need to be replaced. Hide thumbs Also See for L100 Owner's manual - 37 pages 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Note: This auxiliary freeze protection functions at all times, even when another fault condition has occurred and has otherwise shut the spa down. These Codes are Control System Manufacturer SpecificTo determine your Spas control manufacturer look at the systems electronic control box cover (front or back) for the manufacturer.Note: Some Spa assemblers have their Pressure switch is not working. Note: The control system brand name is usually different from the hot tub brand name.

The first thing to do is shut the spa down, remove the filter and make sure all the jets are open. F2 = 4 hours daily filtration F4 = 8 hours daily filtration F6 = 12 hours daily filtration FC = continuous filtration Sundance Spa Side Error Codes ILOC : Interlock failure It has a Gecko T-18 10/31/2016 10/31/2016 rickspaserv I Sorry, I am not familiar with instant messaging. Heater disabled but the spa is operational.SESH = Sensor short, nonfunctional.

System will restart when temp. Heater is shut down, but other spa functions run normally. Contact ACC. Your spa will have one or the other, it will not have both.

drops. Error & LCD Window Message Codes: ACC (Applied Computer Controls) CoLd = Temperature in the spa heater housing is below 40° F. O3S errors relate to the ozone sensor. When I opened the switch manually the test result were infinity.